TLA7PG2 測試碼產生器模組

Tektronix 邏輯分析儀
Tektronix 已不再販售此產品規格表上所列的產品。

線上參閱:

功能與特色

  • 64 通道模組, 向量深度高達 2Mb
  • 時脈速率高達 268 MHz
  • 支援 TTL/CMOS、ECL、PECL/LVPECL、LVDS、LVCMOS 標準邏輯等級
  • 可支援可變電壓值和可變通道間延遲的可變探棒, 以進行功能性驗證
  • 向量輸出的測試碼排序控制, 可供您有彈性地定義複雜事件
  • 可搭配任何 TLA7000 系列邏輯分析儀主機運作

應用

  • 數位硬體驗證與除錯
  • 數位硬體模擬與除錯

即時數位系統分析的突破性解決方案

硬體與軟體工程師, 必須能夠產生數位測試碼, 以便在硬體設計和軟體程式測試中, 模擬不常見的測試條件. 測試碼產生器可供您進行系統硬體設計的功能驗證、除錯和壓力測試. 這個附有串列控制的多通道、可程式設定測試碼產生器模組, 能夠使用來自模擬器的資料激發原形待測物, 進行廣泛的分析. 測試碼產生器非常適合用來設計缺乏一般可提供數位訊號之主機板、IC 和匯流排的系統. 有了測試碼產生器, 您就可以將電路置於想要的狀態, 使其全速運作, 或是透過單一步驟使其經歷一系列的狀態。

TLA7PG 標榜 64 通道, 支援高達 268MHz 的資料輸出速率. 透過外部測試碼產生器探棒的使用, TLA7PG2 可和多種電壓值與技術相容。

TLA7000 系列邏輯分析儀能夠以 SynaptiCAD WaveFormer Pro、VeriLogger Pro 與 TestBencher Pro 軟體工具可讀取的形式擷取波形資料. SynaptiCAD 的工具能夠將 VHDL、Verilog、SPICE、ABEL 和測試碼產生器的邏輯分析儀波形資料轉換成激勵向量, 包括 TLA7PG2. 此功能讓工程師可以運用產品設計階段完成的工作, 簡化了開發一個能提供完整測試涵蓋範圍, 及優秀除錯功能的硬體測試環境之過程。

Characteristics

General

Data Width - 64 Channel full channel mode.32 Channel half channel mode.

Module "Merging" - Up to five modules can be "merged" to make up to a 320 channel module. Merged modules exhibit the same depth as the lesser of the five individual modules.

Number of Mainframe Slots Required -  2.

Data Rate - Internal Clock:0.5 Hz to 134 MHz full channel mode.1.0 Hz to 268 MHz half channel mode.External Clock:DC to 134 MHz full channel mode.DC to 268 MHz half channel mode.

External Clock Input - Polarity: positive or negative.Threshold: -2.56 V to +2.54 V, nominal; programmable in 20 mV increments.Sensitivity: p-p.Impedance: 1 kΩ terminated to ground.

Data Depth - 256 Kb full channel/512 k half channel.1 Mb full channel/2 Mb half channel (optional).

Pattern Sequencing Characteristics

Blocks - Separate sections of pattern program that are output in a user definable order by the Sequencer. Block pattern depth can be from 40 sequences (full channel mode) or 80 sequences (half channel mode) up to the entire depth of the TLA7PG2. A maximum of 4,000 Blocks may be defined.

Sequencer - A 4,000 line memory that allows the user to pick the output order of individual Blocks. Each line in the sequencer allows the definition of a Block to be output, a Repeat Count for that Block, A Wait For event condition for the Block, the Signal state for that Block (asserted or unasserted), and a Jump If event condition, with a sequence line to jump to if the condition is satisfied.

Sub-sequences - Up to 256 contiguous lines of the Sequencer memory may be defined as a Sub-sequence. A Sub-sequence can then be treated like a block. (Example: 15 Sequences of Blocks are defined as Sub-sequence A1. Now any line in the Sequencer can output A1. Five calls to Sub-sequence A1 will be flattened out to 75 sequences at run time.)

Jump If - Jumps to the specified sequence if a user defined event is true. The user defined event is a boolean combination of the eight external event input.

Wait For - Pattern output is paused until the user defined Event is true. One Wait For may be defined for every Block.

Assert Signal - One of the four inter-module signals is selected to be controlled from the pattern generator program. Signals may be asserted and unasserted allowing true interaction with the logic analyzer modules and with other pattern generator modules. Signal action (assert or unassert) may be defined for every Block.

Repeat Count - The sequence is repeated from 1 to 65,536 times. Infinite may also be selected. One Repeat Count may be defined for every block. Note that a repeat value of 10,000 takes one sequence line in memory, not 10,000.

Step - While in Step mode, the TLA7PG2, the user can manually satisfy (i.e., click an icon) Wait For and Jump conditional events. This allows the user to debug the logic flow of the program's sequencing.

Initialization Block - The unconditional Jump command allows the user to implement an equivalent function.

Logic Analyzer/Pattern Generator Connectivity to Simulation Environments - The TLA520x and TLA700 Series logic analyzers capture waveform data in a form that can be read by SynaptiCAD WaveFormer Pro, VeriLogger Pro, and TestBencher Pro software tools. SynaptiCAD's tools can convert the logic analyzer waveform data into stimulus vectors for VHDL, Verilog, SPICE, ABEL, and pattern generators including the TLA7PG2.SynaptiCAD's WaveFormer Pro product offers a timing diagram editing environment that enables stimulus to be created using a combination of graphically drawn signals, timing parameters that constrain edges, clock signals, and temporal and Boolean equations for describing complex, quasi-repetitive signal behavior. Advanced operations on signals such as time scaling and shifting, and block copy and pasting of signal behavior over an interval of time are also supported.

Thumbnail

Easily Create TLA7PG2 Stimulus Files — The TLA7PG2 Pattern Generator stimulus can be created from a mixture of VHDL and Verilog test benches, simulation waveforms, real world data acquired by a logic analyzer, and waveforms created within SynaptiCAD's timing diagram editing environment.

P6470 TTL/CMOS Probe

Number of Data Outputs - 16 in Full Channel Mode.8 in Half Channel Mode.

Number of Clock Outputs - 1. (Only one of Clock Output and Strobe Output can be enabled.)

Number of Strobe Outputs - 1. (Only one of Clock Output and Strobe Output can be enabled.)

Clock Output Polarity - Positive.

Strobe Type - RZ only.

Strobe Delay - Zero or Trailing Edge.

Output Type - HD74LVC541A for Data Output.HD74LVC244A for Clock/Strobe Output.

Rise/Fall Time (20% to 80%) – Timing values measured using 75 Ω termination (internal to probe), 1 MΩ +

Clock/Strobe Output - Rise: 640 ps typical.Fall: 1.1 ns typical.

Data Output - Rise: 680 ps typical.Fall: 2.9 ns typical.

Rise/Fall Time (20% to 80%) – Timing values measured using 75 Ω termination (internal to probe), 510 Ω + 51 pF load and VOH set to 5.0 V.

Clock/Strobe Output - Rise: 6.5 ns typical.Fall: 6.3 ns typical.

Data Output - Rise: 5.2 ns typical.Fall: 4.5 ns typical.

Series Terminator Resistor - 75 Ω standard; 43, 100, and 150 Ω optional.

Output Voltage (nominal, load: 1 MΩ) - VOH: 2.0 V to 5.5 V, tri-stateable, programmable in 25 mV increments.

Data Output Skew -

Data Output to Strobe Output Delay - 1.7 ns typical when strobe delay set to zero.

Data Output to Clock Output Delay - 2.4 ns typical.

External Clock Input to Clock Output Delay - Full channel mode: 61 ns typical.Half channel mode: 61 ns typical.

Number of External Event Inputs -  1.

Number of External Inhibit Inputs -  1.

External Inhibit Input to Output Enable Delay - 34 ns typical for Data Output.

External Inhibit Input to Output Disable Delay - 86 ns typical for Data Output.

Probe D Data Output to Output Enable Delay - (for Internal Inhibit) 7 ns typical for Data Output.

Probe D Data Output to Output Disable Delay - (for Internal Inhibit) 8 ns typical for Data Output.

External Event Input to Clock Output Setup (for inhibit) (event-filter: off) - Full channel mode: 1.5 clocks + 240 ns typical.Half channel mode: 2 clocks + 240 ns typical.

External Event Input and Inhibit Input - Input Type: 74LVC14A.Minimum Pulse Width: 200 ns.

Thumbnail

P6470.

 

P6471 ECL Probe

Number of Data Outputs - 16 in Full Channel Mode.8 in Half Channel Mode.

Number of Clock Outputs - 1. (Only one of Clock Output and Strobe Output can be enabled.)

Number of Strobe Outputs - 1. (Only one of Clock Output and Strobe Output can be enabled.)

Clock Output Polarity - Positive.

Strobe Type - RZ only.

Strobe Delay - Zero or Trailing Edge.

Output Type - 100E151 for data output.100EL16 for strobe output.100EL04 for clock output.All outputs are unterminated.

Rise/Fall Time (20% to 80%) – Timing values measured using 51 Ω to -2.0 V.

Clock Output - Rise: 320 ps typical.Fall: 330 ps typical.

Data Output - Rise: 1200 ps typical.Fall: 710 ps typical.

Strobe Output - Rise: 290 ps typical.Fall: 270 ps typical.

Data Output Skew -

Data Output to Strobe Output Delay - 2.94 ns typical when strobe delay set to zero.

Data Output to Clock Output Delay - 780 ps typical.

External Clock Input to Clock Output Delay - 50 ns typical.

Number of External Event Inputs -  2.

External Event Input - Input Level: ECL. Terminated with 75 KΩ, -2 V.Input Type: 10H116.Minimum Pulse Width: 150 ns.

Thumbnail

P6470.

 

P6472 PECL/LVPECL Probe

Number of Data Outputs - 8 in full channel mode or half channel mode.

Number of Clock Outputs - 1. (only one of clock output and strobe output can be enabled.)

Number of Strobe Outputs - 1. (only one of clock output and strobe output can be enabled.)

Number of External Event Inputs -  2.

Number of External Inhibit Inputs -  0.

Clock Output Polarity - Positive.

Strobe Type - RZ only.

Strobe Delay - Zero or Trailing Edge.

Output Type - 100EP90 for data output.100EP90 for clock/strobe output.

Rise/Fall Time (20% to 80%) - Rise: 330 ps typical.Fall: 970 ps typical.

Output Voltage Level - PECL, LVPECL.

Data Output Skew -

Data Output to Strobe Output Delay - +2.93 ns when strobe delay set to zero.

Data Output to Clock Output Delay - +1.12 ns.

External Clock Input to Clock Output Delay - 50 ns.

Event Input Voltage Level - PECL, LVPECL.

Input Type - 100EL91, unterminated.

Minimum Pulse Width - 150 ns.

Thumbnail

P6472.

 

P6473 LVDS Probe

Number of Data Outputs - 16 in Full Channel Mode.8 in Half Channel Mode.

Number of Clock Outputs - 1. (Only one of Clock Output and Strobe Output can be enabled.)

Number of Strobe Outputs - 1. (Only one of Clock Output and Strobe Output can be enabled.)

Clock Output Polarity - Positive.

Strobe Type - RZ only.

Strobe Delay - Zero or Trailing Edge.

Number of External Event Inputs -  1.

Number of External Inhibit Inputs -  1.

Output Type - LVDS (TIA/EIA-644 compatible) for data output.LVDS (TIA/EIA-644 compatible) for clock/strobe output.

Rise/Fall Time (20% to 80%) - Rise: 910 ps typical.Fall: 750 ps typical.

Data Output Skew -

Data Output to Strobe Output Delay - -280 ps when strobe delay set to zero.

Data Output to Clock Output Delay - 1.2 ns.

External Clock Input to Clock Output Delay - 55 ns.

External Inhibit to Output Enable Delay - 9 ns for data output.

External Inhibit Input to Output Disable Delay - 12 ns for data output.

Probe D Data Output to Output Enable Delay - 2 ns for data output.

Probe D Data Output to Output Disable Delay - 5 ns for data output.

External Event Input to Clock Output Setup - Full Channel Mode: 1.5 Clocks + 180 ns.Half Channel Mode: 2 Clocks + 180 ns.

External Event Input and Inhibit Input - Input Type: LVDS, positive true.Minimum Pulse Width: 150 ns.

Thumbnail

P6473.

 

P6474 LVCMOS Probe

Number of Data Outputs - 16 in Full Channel Mode.8 in Half Channel Mode.

Number of Clock Outputs - 1. (Only one of Clock Output and Strobe Output can be enabled.)

Number of Strobe Outputs - 1. (Only one of Clock Output and Strobe Output can be enabled.)

Clock Output Polarity - Positive.

Strobe Type - RZ only.

Strobe Delay - Zero or Trailing Edge.

Number of External Event Inputs -  2.

Number of External Inhibit Inputs -  1.

Output Type - 74AVC16244 for data, clock, strobe outputs.

Series Terminator Resistor - 75 Ω standard. 43, 100, and 150 Ω optional.

Rise/Fall Time (20% to 80%) - Load: 1 MΩ +

Output Voltage Level - 1.2 V to 3.3 V, 25 mV step, into 1 MΩ.

Data Output Skew -

Data Output to Strobe Output Delay - 460 ps when strobe delay set to zero.

Data Output to Clock Output Delay - 1.84 ns.

External Clock Input to Clock Output Delay - 55 ns.

External Inhibit to Output Enable Delay - 36 ns for data output.

External Inhibit Input to Output Disable Delay - 18 ns for data output.

Probe D Data Output to Output Enable Delay - 6 ns for data output.

Probe D Data Output to Output Disable Delay - 7 ns for data output.

External Event Input to Clock Output Setup - Full Channel Mode: 1.5 clocks + 180 ns.Half Channel Mode: 2 clocks + 180 ns.

External Event Input and Inhibit Input - 74AVC16244, Positive True, 1 kΩ to ground.The Vcc of the input receiver is variable and is the same as the output driver.Minimum Pulse Width: 150 ns.

Thumbnail

P6474.

 

P6475 Variable Probe

Rise/Fall Time (20% to 80%) - Load: 1 MΩ +

Output Voltage Level - VOL: -3 V to 6.5 V, 10 mV step, into 1 MΩ.VOH: -2.5 V to +7 V, 10 mV step, into 1 MΩ.

Output Voltage Swing - 250 mVp-p to 9 Vp-p.

Output Voltage Control - Ch. 0 to Ch. 5: Common.Ch. 6 to Ch. 7, clock: Independent.

Accuracy - ±3% of value ±0.1 V.

Delay Channels - Ch. 6 and Ch. 7 (Independent).

Delay Time - 0 ns to 50 ns with reference to Ch. 0.

Ch. 6 Output Modes - Normal.Ch. 6 OR Ch. 7.Ch. 6 AND Ch. 7.Ch. 6 OR (NOT Ch. 7).Ch. 6 AND (NOT Ch. 7).

Delay Accuracy - ±(3% of Delay Time) ±0.8 ns (to Ch. 0).(At maximum slew rate setting).

Slew Rate Control - 0.5 V/ns to 2.5 V/ns, 100 mV/ns step.

Data Output Skew -

Data Output to Clock Output Delay - 940 ps.

External Clock Input to Clock Output Delay - 62 ns.

Number of External Event Inputs - 2.

Number of External Inhibit Inputs - 1.

External Inhibit to Output Enable Delay - 30 ns for data output.

External Inhibit Input to Output Disable Delay - 28 ns for data output.

Probe D Data Output to Output Enable Delay - -100 ps for data output.

Probe D Data Output to Output Disable Delay - -4.4 ns for data output.

External Event Input to Clock Output Setup - Full Channel Mode: 1.5 Clocks + 180 ns.Half Channel Mode: 2 Clocks + 180 ns.

External Event Input and Inhibit Input - Polarity: Positive True.Impedance: 1 kΩ to ground.Threshold Level: -2.5 V to +2.5 V, Event and Inhibit are independent.Threshold Resolution: 20 mV.Minimum Pulse Width: 150 ns.

Safety - CSA C22.2 No. 1010.1, EN61010-1, IEC61010-1, UL 3111-1

Thumbnail

P6475.

Physical

Physical Characteristics for TLA7PG2

Dimensionsmmin.
Weightkglb.
Height26210.3
Width612.4
Depth38115
Net36.5
Shipping6.213.5

P6470 Probe Cable Length - 1.6 m (5 ft.).

P6471 Probe Cable Length - 1.6 m (5 ft.).

P6472 Probe Cable Length - 1.6 m (5 ft.).

P6473 Probe Cable Length - 1.6 m (5 ft.).

P6474 Probe Cable Length - 1.6 m (5 ft.).

P6475 Probe Cable Length - 1.6 m (5 ft.).

Last Modified:
下載
下載

下載手冊、產品規格表、軟體等等:

Go to top