Ethernet Transmitter Test Application Software
The Ethernet Transmitter Test Application automates 10GBASE-T, NBASE-T, and IEEE802.3bz (2.5G/5G) physical medium attachment (PMA) physical-layer (PHY) electrical testing to provide a fast and accurate way of testing your Ethernet designs.
Notice to EU customers
This product is not updated to comply with the RoHS 2 Directive 2011/65/EU and will not be shipped to the EU. Customers may be able to purchase products from inventory that were placed on the EU market prior to July 22, 2017 until supplies are depleted. Tektronix is committed to helping you with your solution needs. Please contact your local sales representative for further assistance or to determine if alternative product(s) are available. Tektronix will continue service to the end of worldwide support life.
Features and benefits
- Comprehensive automated solution for 2.5GBASE-T, 5GBASE-T and 10GBASE-T PHY testing
- One-button selection of multiple tests and four-channel support
- Detailed test reports with margin and statistical information aid analysis
- User-defined mode enables flexible parameter control for characterization and margin analysis
- Efficient test execution on oscilloscopes with instrument remote control
- Single instrument analysis of time- and frequency-domain measurements
- Signal acquisition and analysis support for differential probes or direct SMA cabling
Based on the TekExpress test automation framework, the Ethernet Transmitter Test Application performs all of the PMA electrical measurements as specified by the 802.3an standard, the 802.3bz standard, and the NBASE-T specification. This allows you to quickly and efficiently test Ethernet devices running at 2.5G, 5G, and 10G data rates.
To accurately make these measurements, the Tektronix TF-XGBT test fixture is also needed. The test fixture allows you to reliable and easily access the device under test (DUT) using either differential probes or matched SMA cables.
Power spectral density measurement.
Test selection and instrument setup
Test selection is easy and straight-forward through the intuitive TekExpress workflow. Simply check the measurements you want to perform.
For each measurement selected, the Ethernet Transmitter application will then automatically set up and configure the oscilloscope saving time and ensuring repeatable, reliable results.
As each test is performed, the application will also show you with detailed diagrams how to properly make the needed connections.
A summary report with Pass/Fail status for each test is created after the tests are complete. This report includes test configuration details, waveform plots, and margin analysis to provide more insight into your design.
You can also make changes to test limits and other test parameters in order to do margin analysis to see how well your device is performing.
Droop configuration parameters
Differential single-ended acquisition support
The application allows signal acquisition and analysis with either matched-pair SMA cables or differential probes.
Differential and single-ended support.
The Ethernet Transmitter Test Application simplifies Return Loss testing and eliminates the need for a Vector Network Analyzer by using a patented oscilloscope-based measurement along with a Tektronix AWG. Calibration data for Open, Load, and Short can be stored in a file and recalled.
Complete programming interface
The programmatic interface seamlessly integrates the Ethernet Transmitter Test application with a high-level automation layer such as Visual Basic, MicrosoftNet, C#, C++, Python, or a Web application. This lets you control the state of the TekExpress application running on a local or a remote computer.
Programming examples are found in the application examples folder.
Prerecorded Waveform support will provide customers an option to use prerecorded waveforms when an oscilloscope is not available. This feature allows waveforms to be shared across multiple locations and removes end-user dependency from using scopes all the time.
- 10GBASE-T Measurements
The following tests are performed per the IEEE802.3-2012 standard. The device under test (DUT) must be able to provide the test mode signals as indicated in IEEE802.3-2012 Subclause 55.5.2.
Measurement Standard reference and Test mode Maximum Output Droop IEEE802.3-2012 Subclause 18.104.22.168 Transmitter Timing Jitter - Master IEEE802.3-2012 Subclause 22.214.171.124 Transmit Clock Frequency IEEE802.3-2012 Subclause 126.96.36.199 Transmitter Timing Jitter - Slave IEEE802.3-2012 Subclause 188.8.131.52 Transmitter Linearity IEEE802.3-2012 Subclause 184.108.40.206 Transmitter Power Spectral Density (PSD) and Power IEEE802.3-2012 Subclause 220.127.116.11 Return Loss IEEE802.3-2012 Subclause 18.104.22.168
- 2.5GBASE-T and 5GBASE-T Measurements (requires NBASET option)
The following tests are performed per IEEE802.3bz/D3.3 draft standard. The device under test (DUT) must be able to provide the test mode signals as indicated in IEEE802.3bz/D3.3 Subclause 126.5.2.
Measurement Test mode Maximum Output Droop IEEE80.bz/D3.3 Subclause 22.214.171.124 Transmitter Timing Jitter - Master IEEE80.bz/D3.3 Subclause 126.96.36.199 Transmit Clock Frequency IEEE80.bz/D3.3 Subclause 188.8.131.52 Transmitter Timing Jitter - Slave IEEE80.bz/D3.3 Subclause 184.108.40.206 Transmitter Nonlinear Distortion IEEE80.bz/D3.3 Subclause 220.127.116.11 Transmitter Power Spectral Density (PSD) and Power IEEE80.bz/D3.3 Subclause 18.104.22.168 Return Loss IEEE80.bz/D3.3 Subclause 22.214.171.124
- NBASE-T Measurements (requires NBASET option)
The following tests are performed per the NBASE-T Physical Layer Specification. The device under test (DUT) must be able to provide the test mode signals as indicated in NBASE-T Physical Layer Specification version 1.1 Subclause 2.9.
Measurement Test mode Maximum Output Droop Subclause 126.96.36.199, Test Mode 6 Transmitter Timing Jitter - Master Subclause 188.8.131.52, Test Mode 2 Transmit Clock Frequency Subclause 184.108.40.206, Test Mode 2 Transmitter Timing Jitter - Slave Subclause 220.127.116.11, Test Mode 1 and Mode 3 Transmitter Nonlinear Distortion Subclause 18.104.22.168, Test Mode 4, Tones 1-5 Transmitter Power Spectral Density (PSD) and Power Subclause 22.214.171.124, Test Mode 5 Return Loss Subclause 126.96.36.199, Test Mode 5