Spectrum Analyzer

Frequency range

RSA503A

9 kHz to 3 GHz

RSA507A

9 kHz to 7.5 GHz

RSA513A

9 kHz to 13.6 GHz

RSA518A

9 kHz to 18.0 GHz

Frequency marker readout accuracy

±(RE × MF + 0.001 × Span) Hz

RE: Reference Frequency Error

MF: Marker Frequency [Hz]

Reference frequency accuracy

Initial accuracy at Cal (30 min warm-up)

±1 x 10^-6

First year aging, typical

±1 x 10^-6 (1 year)

Cumulative error (Initial accuracy + temperature + aging), typical

3 x 10^-6 (1 year)

Temperature drift

±0.9 x 10^-6 (-10 to 60 °C)

External reference input

BNC connector, 50 Ω nominal

External reference input frequency

Every 1 MHz from 1 to 20 MHz plus the following: 1.2288 MHz, 2.048 MHz, 2.4576 MHz, 4.8 MHz, 4.9152 MHz, 9.8304 MHz, 13 MHz, and 19.6608 MHz.

The spurious level on the input signal must be less than -80 dBc within 100 kHz offset to avoid on-screen spurious.

External reference input range

± 5 ppm

External reference input level

-10 to +10 dBm

Accuracy, when locked to GNSS²

±0.025 ppm³

GNSS Trained Accuracy, when GNSS antenna is disconnected ², ⁴

±0.025 ppm⁵

±0.08 ppm⁶

RF Input Impedance

50 Ω

RF VSWR (RF Attn = 20 dB), typical

< 1.2 (10 MHz to 3 GHz)

< 1.5 (>3 GHz to 7.5 GHz)

<1.9 (>7.5 GHz to 18 GHz)

RF VSWR preamp ON, RSA503A and RSA507A, typical

< 1.5 (10 MHz to 6 GHz, RF ATT=10 dB, preamp on)

< 1.7 (> 6 GHz to 7.5 GHz, RF ATT=10 dB, preamp on)

<1.9 (>7.5 GHz to 18 GHz, RF ATT = 10 dB, preamp ON)

Maximum RF input level

Maximum DC voltage

±40 V (RF input)

Maximum safe input power

+33 dBm (RF input, 10 MHz to 18.0 GHz, RF Attn ≥ 20 dB)

+13 dBm (RF input, 9 kHz to 10 MHz, RF Attn ≥ 20 dB)

+20 dBm (RF input, RF Attn < 20 dB)

Maximum safe input power (Preamp On)

+33 dBm (RF input, 10 MHz to 18.0 GHz, RF Attn ≥ 20 dB)

+13 dBm (RF input, 9 kHz to 10 MHz, RF Attn ≥ 20 dB)

+20 dBm (RF input, RF Attn < 20 dB)

Maximum measurable input power

+30 dBm (RF input, ≥10 MHz to Fmax, RF ATT Auto)

+20 dBm (RF input, <10 MHz, RF ATT Auto)

Input RF attenuator

0 dB to 51 dB (1 dB step)

Sweep speed

Full span sweep speed, typical mean ⁷

70 GHz/sec (RBW = 1 MHz)

60 GHz/sec (RBW = 100 kHz)

15.7 GHz/sec (RBW = 10 kHz)

1.7 GHz/sec (RBW = 1 kHz)

Tuning step time via API

≤1 ms

Amplitude and RF flatness

Reference level setting range

-170 dBm to +40 dBm, 0.1 dB step, (Standard RF input)

Frequency response at 18 ℃ to 28 ℃ (At 10 dB RF Attenuator Setting)

Amplitude accuracy at all center frequencies

Center frequency range	18 ⁰C to 28 ⁰C
9 kHz ≤ 3.0 GHz	±0.8 dB
> 3 to 7.5 GHz (RSA507A)	±1.5 dB
>7.5 GHz to 13.6 GHz (RSA513A/RSA518A)	±1.55 dB
>13.6 GHz to 18.0 GHz (RSA518A)	±1.55 dB

Amplitude Accuracy at All Center Frequencies - Preamp ON (18 ℃ to 28 ℃ , 10 dB RF Attenuator)

Center frequency range	18 ⁰C to 28 ⁰C
200 kHz to ≤3.0 GHz	±1.0 dB
> 3 GHz	±3.0 dB

Preamp gain

27 dB at 2 GHz

21 dB at 6 GHz (RSA507A)

25 dB at 10 GHz (RSA513A)

25 dB at 15 GHz (RSA518A)

Channel response (amplitude and phase deviation), typical

For these specifications, use a flat top window for maximum CW amplitude verification accuracy with the RF attenuator setting at 10 dB.

Characteristic		Description
Measurement center frequency	Span	Amplitude flatness, typical	Amplitude flatness, RMS, typical	Phase linearity, RMS, typical
9 kHz to 40 MHz	≤40 MHz 8	±1.0 dB	0.60 dB
>40 MHz to 4.0 GHz	≤20 MHz	±0.10 dB	0.08 dB	0.3°
>4 GHz to 7.5 GHz	≤20 MHz	±0.35 dB	0.20 dB	0.7°
>7.5 GHz to 13.6 GHz	≤20 MHz	±0.35 dB	0.20 dB	0.7°
>13.6 GHz to 18.0 GHz	≤20 MHz	±0.35 dB	0.20 dB	0.7°
>40 MHz to 4 GHz	≤40 MHz	±0.35 dB	0.14 dB	0.8°
>4 GHz to 7.5 GHz	≤40 MHz	±0.40 dB	0.20 dB	1.0°
>7.5 GHz to 13.6 GHz	≤40 MHz	±0.60 dB	0.40 dB	1.5°
>13.6 GHz to 18.0 GHz	≤40 MHz	±0.60 dB	0.40 dB	1.5°

Trigger/Sync input, typical

Voltage range: TTL, 0.0 V to 5.0 V

Trigger level (Schmitt trigger):

Positive-going threshold voltage: 1.6 V min, 2.1 V max

Negative-going threshold voltage: 1.0 V min., 1.35 V max

Impedance: 10 k ohms with schottky clamps to 0 V, +3.4 V

External trigger timing uncertainty

>20 MHz to 40 MHz acquisition bandwidth: ±250 ns

Uncertainty increases as acquisition bandwidth is decreased.

Power trigger

Power trigger, typical

Range: 0 dB to -50 dB from reference level, for trigger levels > 30 dB above the noise floor.

Type: Rising or falling edge

Trigger re-arm time: ≤ 100 μsec

Power trigger position timing uncertainty

>20 MHz to 40 MHz acquisition bandwidth: ±250 ns

Uncertainty increases as acquisition bandwidth is decreased.

Power trigger level accuracy

±1.5 dB for CW signal at tuned center frequency for trigger levels > 30 dB above the noise floor.

This specification is in addition to the overall amplitude accuracy uncertainty for SA mode.

3rd Order IM intercept (TOI)

+14 dBm at 2.130 GHz (RSA503A/RSA507A)

+12 dBm at 2.130 GHz (RSA513A/RSA518A)

3rd Order IM intercept (TOI),

Preamp off, typical

+10 dBm (9 kHz to 25 MHz, RSA503A, RSA507A)

+17 dBm (9 kHz to 25 MHz, RSA513A, RSA517A)

+15 dBm (25 MHz to 3 GHz)

+15 dBm (3 GHz to 4 GHz, RSA507A )

+10 dBm (4 GHz to 7.5 GHz, RSA507A)

+15 dBm (7.5 GHz to Max CF GHz, RSA513A/RSA518A)

Preamp on, typical

-20 dBm (9 kHz to 25 MHz)

-15 dBm (25 MHz to 3 GHz)

-15 dBm (3 GHz to 4 GHz, RSA507A)

-20 dBm (4 GHz to 7.5 GHz, RSA507A)

-15 dBm (7.5 GHz to Max CF, RSA513A/RSA518A)

3rd Order Inter-modulation distortion

-74 dBc at 2.130 GHz (RSA503A/RSA507A)

-78 dBc at 2.130 GHz (RSA513A/RSA518A)

Each signal level -25 dBm at the RF input. 2 MHz tone separation. Attenuator = 0, Reference level = -20 dBm.

3rd Order inter-modulation distortion

Preamp off, typical

< -70 dBc (10 kHz to 25 MHz)

< -80 dBc (25 MHz to 3 GHz)

< -80 dBc (3 GHz to 4 GHz, RSA507A)

< -70 dBc (4 GHz to 7.5 GHz, RSA507A)

< -80 dBc (7.5 GHz to Max CF, RSA513A/RSA518A)

Each signal level -25 dBm at the RF input. 2 MHz tone separation. Attenuator = 0, Reference level = -20 dBm.

Preamp on, typical

< -70 dBc (9 kHz to 25 MHz)

< -80 dBc (25 MHz to 3 GHz)

< -80 dBc (3 GHz to 4 GHz, RSA507A)

< -70 dBc (4 GHz to 7.5GHz, RSA507A)

< -80 dBc (7.5 GHz to Max CF, RSA513A/RSA518A)

Each signal level -55 dBm at the RF input. 2 MHz tone separation. Attenuator = 0, Reference level = -50 dBm.

2nd Harmonic distortion, typical

2nd Harmonic distortion

< -75 dBc (40 MHz to 1.5 GHz)

< -75 dBc (1.5 GHz to 3.75 GHz, RSA507A)

<-75 dBc (3.75 GHz to 6.8 GHz, RSA513A)

<-75 dBc (6.8 GHz to 9 GHz, RSA518A)

2nd Harmonic distortion, Preamp on

< - 60 dBc (40 MHz to 15.9 GHz), input frequency

2nd Harmonic distortion intercept (SHI)

+35 dBm (40 MHz to 1.5 GHz)

+35 dBm (1.5 GHz to 9 GHz)

2nd Harmonic distortion intercept (SHI), Preamp on

+5 dBm (40 MHz to 15.9 GHz), input frequency

Displayed average noise level (DANL)

(Normalized to 1 Hz RBW, with log-average detector)

For the RSA503A and RSA507A:

Frequency range	Preamp on	Preamp on, typical	Preamp off, typical
500 kHz to 1 MHz	-138 dBm/Hz	-145 dBm/Hz	-130 dBm/Hz
1 MHz to 25 MHz	-153 dBm/Hz	-158 dBm/Hz	-130 dBm/Hz
>25 MHz to 1 GHz	-161 dBm/Hz	-164 dBm/Hz	-141 dBm/Hz
>1 GHz to 2 GHz	-159 dBm/Hz	-162 dBm/Hz	-141 dBm/Hz
>2 GHz to 3 GHz	-156 dBm/Hz	-159 dBm/Hz	-138 dBm/Hz
>3 GHz to 4 GHz, RSA507A	-153 dBm/Hz	-156 dBm/Hz	-138 dBm/Hz
>4 GHz to 6 GHz, RSA507A	-159 dBm/Hz	-162 dBm/Hz	-147 dBm/Hz
>6 GHz to 7.5 GHz, RSA507A	-155 dBm/Hz	-158 dBm/Hz	-145 dBm/Hz

For the RSA513A and RSA518A:

Frequency range	Preamp on	Preamp on, typical
500 kHz to 1 MHz	-138 dBm/Hz	-145 dBm/Hz
1 MHz to 25 MHz	-153 dBm/Hz	-158 dBm/Hz
>25 MHz to 1 GHz	-158 dBm/Hz	-161 dBm/Hz
>1 GHz to 2 GHz	-156 dBm/Hz	-159 dBm/Hz
>2 GHz to 2.75 GHz	-153 dBm/Hz	-157 dBm/Hz
>2.75 GHz to 4 GHz	-149 dBm/Hz	-152 dBm/Hz
>4 GHz to 6 GHz	-155 dBm/Hz	-159 dBm/Hz
>6 GHz to 7.5 GHz	-151 dBm/Hz	-155 dBm/Hz
>7.5 GHz to 14 GHz	-161 dBm/Hz	-165 dBm/Hz
>14 GHz to 14.8 GHz	-159 dBm/Hz	-165 dBm/Hz
>14.8 GHz to 15.2 GHz	-157 dBm/Hz	-161 dBm/Hz
>15.2 GHz to 17.65 GHz	-159 dBm/Hz	-165 dBm/Hz
>17.65 GHz to 18.0 GHz	-157 dBm/Hz	-161 dBm/Hz

Phase noise

Offset	10 kHz	100 kHz	1 MHz
1 GHz CF	-94 dBc/Hz	-94 dBc/Hz	-116 dBc/Hz
10 MHz, typical (RSA503A, RSA507A)	-120 dBc/Hz	-124 dBc/Hz	-124 dBc/Hz
1 GHz CF (typical)	-97 dBc/Hz	-98 dBc/Hz	-121 dBc/Hz
2 GHz CF (typical)	-96 dBc/Hz	-97 dBc/Hz	-120 dBc/Hz
6 GHz CF, typical (RSA507A)	-94 dBc/Hz	-96 dBc/Hz	-120 dBc/Hz
10 GHz, typical (RSA513A, RSA518A)	-89 dBc/Hz	-90 dBc/Hz	-113 dBc/Hz
15 GHz, typical (RSA513A, RSA518A)	-86 dBc/Hz	-87 dBc/Hz	-110 dBc/Hz

Residual spurious response (Reference = -30 dBm, RBW = 1 kHz)

<-75 dBm (500 kHz to 60 MHz), typical

< -85 dBm (>60 MHz to 80 MHz), typical

<-100 dBm (>80 MHz to Max CF), typical

(Exceptions: <-90 dBm (13.78 GHz to 13.94 GHz))

Spurious response with Signal (Image suppression)

< -65 dBc (for RSA513/518A) (10 kHz to Max CF, Ref= -20 dBm, Atten = 10 dB, RF input Level = -20 dBm, RBW = 10 Hz)

< -63 dBc (for RSA503A/507A) (10 kHz to Max CF, Ref= -20 dBm, Atten = 10 dB, RF input Level = -20 dBm, RBW = 10 Hz)

Spurious response with signal at CF

Offset ≥ 1 MHz

Frequency	Span ≤40 MHz, swept spans >40 MHz
1 MHz - 100 MHz	--	-75 dBc
100 MHz - 3 GHz	-72 dBc	-75 dBc
3 GHz - 7.5 GHz (RSA507A)	-72 dBc	-75 dBc
7.5 GHz to 13.6 GHz (RSA513A/RSA518A)	-72 dBc	-75 dBc
13.6 GHz to 18.0 GHz (RSA518A)	-72 dBc	-75 dBc

Spurious response with signal at CF

(150 kHz ≤ offset <1 MHz, Span=2 MHz ):

Frequency	Typical
1 MHz - 100 MHz	-70 dBc
100 MHz - 3 GHz	-70 dBc
3 GHz - 7.5 GHz (RSA507A)	-70 dBc
7.5 GHz - 13.6 GHz (RSA513A/RSA518A)	-64 dBc
13.6 GHz - 18.0 GHz (RSA518A)	-64 dBc

Spurious response with signal at other than CF, typical

Frequency	Span ≤40 MHz, swept spans >40 MHz
1 MHz – 25 MHz (LF Band)	-73 dBc
25 MHz – 3 GHz	-73 dBc
3 GHz – 7.5 GHz (RSA507A)	-73 dBc
7.5 GHz - 13.6 GHz (RSA513A/RSA518A)	-73 dBc
13.6 GHz - 18.0 GHz (RSA518A)	-73 dBc

Spurious response with signal at half-IF ⁹

< -75 dBc, (CF: 30 MHz to Max CF, Ref = -20 dBm, Atten = 10 dB, RBW = 10 Hz, Span = 10 kHz)

Signal frequency = 2310 MHz, RF input level = -20 dBm

Local oscillator feed-through to input connector, typical

< -70 dBm, preamp off.

< -90 dBm, preamp on.

Attenuator = 10 dB.

IF bandwidth

40 MHz.

A/D converter

14 bits, 112 Ms/s.

Real-Time IF Acquisition Data

112 Ms/s, 16-bit integer samples.

ACLR for 3GPP Down Link, 1 DPCH (2130 MHz)

-57 dB (Adjacent Channel)

-68 dB w/Noise Correction (Adjacent Channel)

-57 dB (First Alternate Channel)

-69 dB w/Noise Correction (First Adjacent Channel)

ACLR LTE

-58 dB (Adjacent Channel)

-61 dB w/Noise Correction (Adjacent Channel)

-61 dB (First Alternate Channel)

-63 dB w/Noise Correction (First Adjacent Channel)

Format

GPS/GLONASS/BeiDou

GPS antenna power

3 V, 100 mA maximum

Time to first fix, maximum

Lock time ranges from 2 sec (hot) to 46 sec (cold start).

-130 dBm input signal power.

Horizontal position accuracy

GPS: 2.6 m

Glonass: 2.6 m

BeiDou: 10.2 m

GPS + Glonass: 2.6 m

GPS + BeiDou: 2.6 m

Test conditions: 24 hr. static, -130 dBm, full power

Tracking Generator (Option 04)

Frequency range

Reflection	9 kHz - 3.0 GHz (RSA503A) 9 kHz - 7.5 GHz (RSA507A/513A/518A)
Transmission	10 MHz to 3 GHz (RSA503) 10 MHz to 7.5 GHz (RSA507A/513A/518A)

Sweep speed, typical mean

0.192 sec/sweep, 101 points, 50 kHz RBW, 980 to 1020 MHz sweep (1.9 mS per point)

Measured using a Dell Latitude E5540, i7, Windows^®7 Pro. Transmission Gain display is only measurement on screen.

Frequency resolution

100 Hz

TG output connector

N type

VSWR

< 1.9:1, 10 MHz to 7.5 GHz, -20 dBm output level

Maximum output power

-3 dBm,10 MHz to 7.5 GHz

Output power level setting range

40 dB, 10 MHz to 7.5 GHz

Output power level step size

1 dB, 10 MHz to 7.5 GHz

Output power level step size accuracy

± 0.5 dB

Harmonics

< -22 dBc, ≥20 MHz

Non-harmonic spurious

< -30 dBc; spurious < 2 GHz from TG output frequency

< -25 dBc; spurious ≥ 2 GHz from TG output frequency

Reverse power without damage

40 Vdc, +20 dBm RF

Measurements included.

General signal analysis
Spectrum analyzer	Spans from 1 kHz to 18.0 GHz Three traces plus math and spectrogram trace Five markers with power, relative power, integrated power, power density and dBc/Hz functions
DPX Spectrum/Spectrogram	Real time display of spectrum with 100% probability of intercept of up to 15 μsec signals in up to 40 MHz span
Amplitude, frequency, phase vs. time, RF I and Q vs. time	Basic vector analysis functions
Time Overview/Navigator	Enables easy setting of acquisition and analysis times for deep analysis in multiple domains
Spectrogram	Analyze and re-analyze your signal with a 2-D or 3-D waterfall display
AM/FM listening	Hear, and record to file, FM and AM signals
Signal recording	Record 40 MHz bandwidth gap-free in .r3f file format for re-analysis in all domains including real time spectrum analysis (requires option SV56 installed in PC controller for Playback)
Analog modulation analysis
AM, FM, PM analysis	Measures key AM, FM, PM parameters
RF measurements
Spurious measurement	User-defined limit lines and regions provide automatic spectrum violation testing across the entire range of the instrument. Four traces can be saved and recalled; CISPR Quasi-Peak and Average detectors available with option SVQP.
Spectrum emission mask	User-defined or standards-specific masks
Occupied Bandwidth	Measures 99% power, -xdB down points
Channel Power and ACLR	Variable channel and adjacent/alternate channel parameters
MCPR	Sophisticated, flexible multi-channel power measurements
CCDF	Complementary Cumulative Distribution Function plots the statistical variations in signal level

Maximum span

40 MHz real-time

9 kHz - 3 GHz swept (RSA503A)

9 kHz - 7.5 GHz swept (RSA507A)

9 kHz - 13.6 GHz swept (RSA513A)

9 kHz - 18.0 GHz swept (RSA518A)

Maximum acquisition time

2.0 s

Minimum IQ resolution

17.9 ns (acquisition BW = 40 MHz)

Tuning Tables

Tables that present frequency selection in the form of standards-based channels are available for the following.

Cellular standards families: AMPS, NADC, NMT-450, PDC, GSM, CDMA, CDMA-2000, 1xEV-DO WCDMA, TDSCDMA, LTE, WiMax

Unlicensed short range: 802.11a/b/j/g/p/n/ac, Bluetooth

Cordless phone: DECT, PHS

Broadcast: AM, FM, ATSC, DVBT/H, NTSC

Mobile radio, pagers, other: GMRS/FRS, iDEN, FLEX, P25, PWT, SMR, WiMax

DPX spectrum display

Spectrum processing rate (RBW = auto, trace length 801)

≤10,000 spectrums per second

DPX bitmap resolution

201 pixels vertical x 801 pixels horizontal

DPX Spectrogram minimum time resolution ¹⁰

1 ms

≤10,000 per second (span independent)

Marker information

Amplitude, frequency, signal density

Minimum signal duration for 100% probability of intercept (POI), typical ¹¹

15 μs up to 40 MHz span

Span range (continuos processing)

1 kHz to 40 MHz

Span range (swept)

Up to maximum frequency range of instrument

Dwell time per step

50 ms to 100 s

Trace processing

Color-graded bitmap, +Peak, -Peak, average

Trace length

801, 2401, 4001, 10401

RBW range

1 kHz to 4.99 MHz

DPX spectrogram display

Trace detection

+Peak, -Peak, Average(V_RMS)

Trace length, memory depth

801 (60,000 traces)

2401 (20,000 traces)

4001 (12,000 traces)

Time resolution per line

1 ms to 6400 s, user selectable

Spectrum and Spurious display

Traces

Three traces + 1 math trace + 1 trace from spectrogram for Spectrum display; four traces for Spurious display

Trace functions

Normal, Average (VRMS), Max Hold, Min Hold, Average of Logs

Detector

Average (VRMS), Average (of logs), CISPR peak, +Peak, Sample for Spectrum only -Peak; when Option SVQP is enabled, CISPR Quasi Peak and Average

Spectrum trace length

801, 2401, 4001, 8001,10401, 16001, 32001, and 64001 points

RBW range

1.18 Hz to 8 MHz for Spectrum display

Analog modulation analysis (standard)

AM demodulation accuracy typical

±2%

0 dBm input at center, carrier frequency 1 GHz, 1 kHz/5 kHz input/modulated frequency, 10% to 60% modulation depth

0 dBm input power level, reference level = 10 dBm, Atten=Auto

FM demodulation accuracy, typical

±1% of span

0 dBm input at center, carrier frequency 1 GHz, 400 Hz/1 kHz input/modulated frequency

0 dBm input power level, reference level = 10 dBm, Atten=Auto

PM demodulation accuracy, typical

±3% of measurement bandwidth

0 dBm input at center, carrier frequency 1 GHz, 1 kHz/5 kHz input/modulated frequency

0 dBm input power level, reference level = 10 dBm, Atten=Auto

AM/FM/PM and direct audio measurement (SVAxx-SVPC)

Carrier frequency range (for modulation and audio measurements)

(1/2 × audio analysis bandwidth) to maximum input frequency

Maximum audio frequency span

10 MHz

FM measurements (Mod. index >0.1)

Carrier Power, Carrier Frequency Error, Audio Frequency, Deviation (+Peak, -Peak, Peak-Peak/2, RMS), SINAD, Modulation Distortion, S/N, Total Harmonic Distortion, Total Non-harmonic Distortion, Hum and Noise

AM measurements

Carrier Power, Audio Frequency, Modulation Depth (+Peak, -Peak, Peak-Peak/2, RMS), SINAD, Modulation Distortion, S/N, Total Harmonic Distortion, Total Non-harmonic Distortion, Hum and Noise

PM measurements

Carrier Power, Carrier Frequency Error, Audio Frequency, Deviation (+Peak, -Peak, Peak-Peak/2, RMS), SINAD, Modulation Distortion, S/N, Total Harmonic Distortion, Total Non-harmonic Distortion, Hum and Noise

Audio filters

Low pass, kHz: 0.3, 3, 15, 30, 80, 300, and user-entered up to 0.9 × audio bandwidth

High pass, Hz: 20, 50, 300, 400, and user-entered up to 0.9 × audio bandwidth

Standard: CCITT, C-Message

De-emphasis (μs): 25, 50, 75, 750, and user-entered

File: User-supplied .TXT or .CSV file of amplitude/frequency pairs. Maximum 1000 pairs

Performance characteristics, typical	Conditions: Unless otherwise stated, performance is given for: Modulation rate = 5 kHz AM depth: 50% PM deviation 0.628 Radians
	FM	AM	PM	Conditions
Carrier Power accuracy	Refer to instrument amplitude accuracy
Carrier Frequency accuracy	± 0.5 Hz + (transmitter frequency × ref. freq. error)	Refer to instrument frequency accuracy	± 0.2 Hz + (transmitter frequency × ref. freq. error)	FM deviation: 5 kHz /100 kHz
Depth of Modulation accuracy	NA	± 0.2%+(0.01 * measured value)	NA	Rate: 5 kHz Depth: 50%
Deviation accuracy	± (1% × (rate + deviation)+50 Hz)	NA	± 100% * (0.01 +(measured rate/1 MHz))	FM deviation: 100 kHz
Rate accuracy	± 0.2 Hz	± 0.2 Hz	± 0.2 Hz	FM deviation: 5 kHz / 100 kHz
Residual THD	0.10%	0.16%	0.1%	FM Deviation: 5 kHz / 100 kHz Rate: 1 kHz
Residual SINAD	43 dB	56 dB	40 dB	FM deviation 5 kHz FM deviation 100 kHz Rate: 1 kHz

APCO P25 Measurements Application (SV26xx-SVPC)

Measurements

RF output power, operating frequency accuracy, modulation emission spectrum, unwanted emissions spurious, adjacent channel power ratio, frequency deviation, modulation fidelity, frequency error, eye diagram, symbol table, symbol rate accuracy, transmitter power and encoder attack time, transmitter throughput delay, frequency deviation vs. time, power vs. time, transient frequency behavior, HCPM transmitter logical channel peak adjacent channel power ratio, HCPM transmitter logical channel off slot power, HCPM transmitter logical channel power envelope, HCPM transmitter logical channel time alignment, cross-correlated markers

Modulation fidelity, typical

C4FM ≤ 1.0%

HCPM ≤ 0.5%

HDQPSK ≤ 0.25%

Input signal level is optimized for best modulation fidelity.

Bluetooth Measurements Application (SV27xx-SVPC and SV31xx-SVPC)

Supported standards

Bluetooth^® 4.2 Basic Rate, Bluetooth^® 4.2 Low Energy, Bluetooth^® 4.2 Enhanced Data Rate. Bluetooth^® 5 when SV31 is enabled.

Measurements

Peak Power, Average Power, Adjacent Channel Power or InBand Emission mask, -20 dB Bandwidth, Frequency Error, Modulation Characteristics including ΔF₁avg (11110000), ΔF₂avg (10101010), ΔF₂ > 115 kHz, ΔF₂/ΔF₁ ratio, frequency deviation vs. time with packet and octet level measurement information, Carrier Frequency f₀, Frequency Offset (Preamble and Payload), Max Frequency Offset, Frequency Drift f₁-f₀, Max Drift Rate f_n-f₀ and f_n-f_n-5, Center Frequency Offset Table and Frequency Drift table, color-coded Symbol table, Packet header decoding information, eye diagram, constellation diagram

Output power (BR and LE), typical mean

Supported measurements: Average power, peak power

Level uncertainty: refer to instrument amplitude and flatness specification

Measurement range: signal level > –70 dBm

Modulation characteristics, typical mean

Supported measurements: ΔF₁avg, ΔF₂avg, ΔF₂avg/ ΔF₁avg, ΔF₂max%>=115kHz (basic rate), ΔF₂max%>=115kHz (low energy)

Deviation range: ±280 kHz

Deviation uncertainty (at 0 dBm):

<2 kHz ¹² + instrument frequency uncertainty (basic rate)

<3 kHz ¹² + instrument frequency uncertainty (low energy)

Measurement range: Nominal channel frequency ±100 kHz

Initial Carrier Frequency Tolerance (ICFT) (BR and LE), typical mean

Measurement uncertainty (at 0 dBm): <1 kHz ¹² + instrument frequency uncertainty

Measurement range: Nominal channel frequency ±100 kHz

Carrier Frequency Drift (BR and LE), typical mean

Supported measurements: Max freq. offset, drift f₁- f₀, max drift f_n-f₀, max drift f_n-f_n-5 (BR and LE 50 μs)

Measurement uncertainty: <1 kHz + instrument frequency uncertainty

Measurement range: Nominal channel frequency ±100 kHz

In-band emissions (ACPR) (BR and LE)

Level uncertainty: refer to instrument amplitude and flatness specification

General-purpose digital modulation analysis (SVMxx-SVPC)

Modulation formats

BPSK, QPSK, 8PSK, 16QAM, 32QAM, 64QAM, 128QAM, 256QAM, 1024QAM, π/2DBPSK, DQPSK, π/4DQPSK, D8PSK, D16PSK, SBPSK, OQPSK, SOQPSK, 16-APSK, 32-APSK, MSK, CPM, 2FSK, 4FSK, 8FSK, 16FSK, C4FM

Analysis period

Up to 163,500 samples

Filter rolloff factor

α：0.001 to 1, in 0.001 steps

Vector diagram display format

Symbol/locus display, Frequency Error measurement, Origin Offset measurement

LTE Downlink RF measurements (SV28xx-SVPC)

Standard Supported

3GPP TS 36.141 Version 12.5

Frame Format supported

FDD and TDD

Measurements and Displays Supported

Adjacent Channel Leakage Ratio (ACLR), Spectrum Emission Mask (SEM), Channel Power, Occupied Bandwidth, Power vs. Time showing Transmitter OFF power for TDD signals and LTE constellation diagram for Primary Synchronization Signal and Secondary Synchronization Signal with Cell ID, Group ID, Sector ID, RS (Reference Signal) Power and Frequency Error.

Mapping (MAPxx-SVPC)

Supported map types

Pitney Bowes MapInfo (*.mif), Bitmap (*.bmp), Open Street Maps (.osm)

Saved measurement results

Measurement data files (exported results)

Map file used for the measurements

Google Earth KMZ file

Recallable results files (trace and setup files)

MapInfo-compatible MIF/MID files

Measurements (nominal)

Pulse-Ogram™ waterfall display of multiple segmented captures, with amplitude vs time and spectrum of each pulse. Pulse frequency, Delta Frequency, Average on power, Peak power, Average transmitted power, Pulse width, Rise time, Fall time, Repetition interval (seconds), Repetition interval (Hz), Duty factor (%), Duty factor (ratio), Ripple (dB), Ripple (%), Droop (dB), Droop (%), Overshoot (dB), Overshoot (%), Pulse- Ref Pulse frequency difference, Pulse- Ref Pulse phase difference, Pulse- Pulse frequency difference, Pulse- Pulse phase difference, RMS frequency error, Max frequency error, RMS phase error, Max phase error, Frequency deviation, Phase deviation, Impulse response (dB), Impulse response (time), Time stamp.

Minimum pulse width for detection, typical

150 ns

Average ON power at 18 °C to 28 °C, typical

±0.4 dB + absolute amplitude accuracy

For pulses of 300 ns width or greater, duty cycles of .5 to .001, and S/N ratio ≥ 30 dB

Duty factor, typical

±0.2% of reading

For pulses of 450 ns width or greater, duty cycles of .5 to .001, and S/N ratio ≥ 30 dB

Average transmitted power, typical

±0.5 dB + absolute amplitude accuracy

For pulses of 300 ns width or greater, duty cycles of .5 to .001, and S/N ratio ≥ 30 dB

Peak pulse power, typical

±1.2 dB + absolute amplitude accuracy

For pulses of 300 ns width or greater, duty cycles of .5 to .001, and S/N ratio ≥ 30 dB

Pulse width, typical

±0.25% of reading

For pulses of 450 ns width or greater, duty cycles of .5 to .001, and S/N ratio ≥ 30 dB

Playback of recorded signals (SV56)

Playback file type

R3F recorded by RSA306, RSA500, or RSA600

Recorded file bandwidth

40 MHz

File playback controls

General: Play, stop, exit playback

Location: Begin/end points of playback settable from 0-100%

Skip: Defined skip size from 73 μs up to 99% of file size

Live rate: Plays back at 1:1 rate to recording time

Loop control: Play once, or loop continuously

Memory requirement

Recording of signals requires storage with write rates of 300 MB/sec. Playback of recorded files at live rates requires storage with read rates of 300 MB/sec.

WLAN Measurements, 802.11a/b/g/j/p (SV23xx-SVPC)

Measurements

WLAN power vs. time; WLAN symbol table; WLAN constellation; spectrum emission mask; error vector magnitude (EVM) vs. symbol (or time), vs subcarrier (or frequency); mag error vs symbol (or time), vs. subcarrier (or frequency); phase error vs symbol (or time), vs. subcarrier (or frequency); channel frequency response vs. symbol (or time), vs. subcarrier (or frequency); spectralflatness vs. symbol (or time), vs. subcarrier (or frequency)

Residual EVM - 802.11a/g/j /p (OFDM), 64-QAM, typical

2.4 GHz, 20 MHz BW: -39 dB

5.8 GHz, 20 MHz BW: -38 dB

Input signal level optimized for best EVM, average of 20 bursts, ≥16 symbols each

Residual EVM - 802.11b, CCK-11, typical

2.4 GHz, 11 Mbps: 1.3 %

Input signal level optimized for best EVM, average of 1,000 chips, BT = .61

WLAN Measurements 802.11n (SV24xx-SVPC)

Measurements

WLAN power vs. time; WLAN symbol table; WLAN constellation; spectrum emission mask; error vector magnitude (EVM) vs. symbol (or time), vs subcarrier (or frequency); mag error vs symbol (or time), vs. subcarrier (or frequency); phase error vs symbol (or time), vs. subcarrier (or frequency); channel frequency response vs. symbol (or time), vs. subcarrier (or frequency); spectralflatness vs. symbol (or time), vs. subcarrier (or frequency)

EVM performance - 802.11n, 64-QAM, typical

2.4 GHz, 40 MHz BW: -39 dB

5.8 GHz, 40 MHz BW: -38 dB

Input signal level optimized for best EVM, average of 20 bursts, ≥16 symbols each

WLAN Measurements 802.11ac (SV25xx-SVPC)

Measurements

WLAN power vs. time; WLAN symbol table; WLAN constellation; spectrum emission mask; error vector magnitude (EVM) vs. symbol (or time), vs subcarrier (or frequency); mag error vs symbol (or time), vs. subcarrier (or frequency); phase error vs symbol (or time), vs. subcarrier (or frequency); channel frequency response vs. symbol (or time), vs. subcarrier (or frequency); spectralflatness vs. symbol (or time), vs. subcarrier (or frequency)

EVM performance - 802.11ac, 256-QAM, typical

5.8 GHz, 40 MHz BW: -38 dB

Input signal level optimized for best EVM, average of 20 bursts, ≥16 symbols each

EMC pre-compliance and troubleshooting (EMCVUxx-SVPC)

Standards

EN55011, EN55012, EN55013, EN55014, EN55015, EN55025, EN55032, EN60601, DEF STAN, FCC Part 15, FCC Part18, MIL-STD 461G

Features

EMC-EMI display, Wizard to setup accessories and limit lines, Inspect, Harmonic Markers, Level Target, Compare Traces, Measure Ambient, Report generation, Re-measure Spot

Detectors

+Peak, Avg, Avg (of logs), Avg (VRMS), CISPR QuasiPeak, CISPR Peak, CISPR Average, CISPR Average of Logs, MIL +Peak, DEF STAN Avg, DEF STAN Peak

Limit lines

Up to 3 Limit Lines with corresponding margins

Resolution BW

Set per standard or user definable

Dwell time

Set per standard or user definable

Report format

PDF, HTML, MHT,RTF, XLSX, Image File format

Accessory type

Antenna, Near Field Probe, Cable, Amplifier, Limiter, Attenuator, Filter, Other

Correction format

Gain/Loss Constant, Gain/loss table, Antenna Factor

Traces

Save/recall up to 5 traces, Math trace (trace1 minus trace2), Ambient trace

Return Loss, Distance-to-Fault, and Cable Loss measurements

Measurements

Return Loss, Cable Loss, Distance-to-Fault (DTF)

Frequency range

10 MHz to 3 GHz (RSA503A)

10 MHz to 7.5 GHz (RSA507A/513A/518A)

Sweep speed¹³

5 ms/point, Return Loss measurement

5 ms/point, Distance-to-Fault measurement

5 ms/point, Cable Loss measurement

Frequency resolution

500 Hz

Return Loss measurement error

Return Loss of 0 to 15 dB: ±0.5 dB

Return Loss of 15 to 25 dB: ±1.5 dB

Return Loss of 25 to 35 dB: ±4.0 dB

Return Loss measurement error at 14 dB Return Loss

±1.5 dB from 10 MHz to 6.8 GHz

±3.0 dB from 6.8 GHz to 7.5 GHz

Return Loss measurement range

50 dB

Interference immunity

Return Loss Measurement Error within specifications for the following conditions:

+5 dBm interferer power within 800 kHz of measurement point

+5 dBm interferer power more than 800 kHz away from measurement point

(High power test level. Interferer not included in accuracy assessment.)

Distance-to-Fault range

1500 m or 15 dB one-way cable loss capable, user defined

Maximum range is a function of the cable velocity factor and the frequency step size as follows:

Where:

V_p = Cable velocity factor relative to the speed of light

c = Speed of light (m/s)

F_start = Sweep start frequency (Hz)

F_stop = Sweep stop frequency (Hz)

N = number of sweep points

Distance-to-Fault resolution

RSA503A, (RG-58Vp=0.66): 0.03 m (User Definable)

RSA507A, (RG-58Vp=0.66): 0.01 m (User Definable)

Minimum resolution is a function of the cable velocity factor and the frequency step size as follows:

or

Inputs, outputs, and inferfaces

RF input

RSA503A/507A: N type, female

RSA513A/518A: N type, female (ships standard with this connector)

RSA513A/518A: Planar Crown, 50 Ω. Users can select this connector instead of the N type in order to select the connector that best fits their applications. (Users can use adapters compatible with the planar crown that best fits their application.)

External frequency reference input

BNC, female

Trigger/Sync input

BNC, female

Tracking Generator Source Output

N type, female

GPS Antenna

SMA, female

USB Device Port

USB 3.0 – Type A

USB Status LED

LED, dual color red/green

LED states:

Steady Red: USB power applied, or resetting

Steady Green: Initialized, ready for use

Blinking Green: Transferring data to host

Battery Status LED

LED, green

LED states:

Blinking Green: External power connected, charging battery

Off – no external power connected or battery fully charged

Maximum power dissipation (fully loaded)

15 W maximum. Maximum line current is 0.2 A at 90 V line.

Surge current

2 A peak maximum, at 25 °C (77 °F) for ≤ 5 line cycles, after the product has been turned off for at least 30 seconds.

Cooling clearance

Bottom, top

25.4 mm ( 1.0 in.)

Sides

25.4 mm (1.0 in.)

Rear: 25.4 mm (1.0 in.)

External DC input

Voltage

18 V

Voltage range limits

Operation: +12.0 V to +19.95 V

Battery Charging: +17.5 V to +19.95 V

Connector type

2.5 mm male

Center conductor: positive

Outer conductor: negative

AC Adapter Output

18 V ± 5%, 5 A (90 W max)

Center conductor: positive

Outer conductor: negative

Battery

Nominal voltage

14.4 V

Nominal capacity

6140 mAh

Battery technology

Li-Ion, Smart Battery compatible with SMBus interface.

Battery operational life

4 hours of continuous operation per battery

Battery operating temperature

Operating (discharge) ¹⁴: -10 °C to +45 °C (14 °F to 113 °F) ¹⁵

Charging: 0 °C to 45 °C (32 °F to 113 °F)

Battery storage life

2 years at +20 °C (68 °F) nominal

Max storage duration between recharge: 10 months @ +20 °C (68 °F)

Physical characteristics

Height

67.3 mm (2.65 in)

Width

299.1 mm (11.78 in)

Depth

271.3 mm (10.68 in)

Net weight

RSA503A/507A: 2.54 kg (5.6 pounds) without battery 2.99 kg (6.6 pounds) with battery

RSA513A/518A: 3.40 kg (7.5 pounds) without battery 3.85 kg (8.5 pounds) with battery

Temperature

Without battery installed

Operating: -10 °C to +55 °C (+14 °F to +131 °F)

Non-operating: -51 °C to +71 °C (-60 °F to +160 °F)

With battery installed

Operating (discharge)¹⁴ : -10 °C to +45 °C (+14 °F to +113 °F)¹⁵

Charging: 0 °C to 45 °C (32 °F to +113 °F)

Humidity

Without battery Installed

MIL-PRF-28800F Class 2

Operating:

5% to 95±5%RH (relative humidity) in the temperature range of +10 °C to 30 °C (+50 °F to 86 °F)

5% to 75±5% RH above +30 °C to 40 °C (+86 °F to 104 °F)

5% to 45±5% RH above +40 °C up to +55 °C (+86 °F to +131 °F)

<10 °C (+50 °F) humidity is uncontrolled; non-condensing

With battery Installed

Operating:

5% to 95% RH (relative humidity) in the temperature range of +10 °C to 30 °C (+14 °F to +86 °F)

5% to 45% RH above +30 °C to 50 °C (+86 °F to 122 °F)

<10 °C (+50 °F) humidity is uncontrolled; non-condensing

Altitude

Operating

Up to 5000 m (16,404 ft.)

Non-operating

Up to 15240 m (50,000 ft.)

Exposure

Splash-Proof test, operating and non-operating

No potential of shock hazard after exposure to non-operating Splash Proof Test per IEC529, level IP52

Dust resistance test, operating and non-operating

Test method per IEC529, level IP52, test conditions 13.4 and 13.5.

Salt exposure test, structural parts

Standard MIL-STD-810, Method 509.1, Procedure 1

Vibration

Operating

Tektronix Class 2 Random Vibration Test at 2.66 GRMS: 5-500 Hz, 3 Axes at 10 min/axis

Non-Operating

MIL-PRF-28800F Class 2

0.030 g²/Hz., 10 500 Hz, 30 minutes per axis, 3 axes (90 minutes total)

Shock

Operating

Test method per Military Standard MIL-PRF-28800F 1-4

Non-Operating

Exceeds the requirements of Military Standard MIL-PRF-28800F

Handling and transit

Bench handling, operating

MIL-PRF-28800F Class 2

Transit drop, non-operating

MIL-PRF-28800F Class 2

Free-Fall drop, non-operating

32 inches

RSA503A: USB real time spectrum analyzer, 9 kHz - 3.0 GHz, 40 MHz acquisition bandwidth

RSA507A: USB real time spectrum analyzer, 9 kHz - 7.5 GHz, 40 MHz acquisition bandwidth

RSA513A: USB real time spectrum analyzer, 9 kHz - 13.6 GHz, 40 MHz acquisition bandwidth

RSA518A: USB real time spectrum analyzer, 9 kHz - 18.0 GHz, 40 MHz acquisition bandwidth

The RSA500 series instruments require a PC with Windows 7, Windows 8/8.1, or Windows 10, 64-bit operating system and a USB 3.0 connection. 8 GB RAM and 20 GB free drive space is required for installation of SignalVu-PC. For full performance of the real time features of the RSA500 , an Intel Core i7 4th generation processor is required. Processors of lower performance can be used, with reduced real-time performance. Storage of streaming data requires that the PC be equipped with a drive capable of streaming storage rates of 300 MB/sec.

Includes: USB 3.0 cable (2 M), A-A connection, screw lock, shoulder strap, carrying case (with room for unit, tablet, accessories), quick-start manual (printed), connector covers, WFM200BA Li-Ion rechargeable battery pack, WFM200BA Li-Ion battery pack instructions (printed), AC power adapter, power cord (see power plug options), USB memory device with SignalVu-PC, API and documentation files. A GPS antenna is not included with the instrument. See Accessories for available GPS antennas.

Opt. A0

North America power plug (115 V, 60 Hz)

Opt. A1

Universal Euro power plug (220 V, 50 Hz)

Opt. A2

United Kingdom power plug (240 V, 50 Hz)

Opt. A3

Australia power plug (240 V, 50 Hz)

Opt. A4

North America power plug (240 V, 50 Hz)

Opt. A5

Switzerland power plug (220 V, 50 Hz)

Opt. A6

Japan power plug (100 V, 50/60 Hz)

Opt. A10

China power plug (50 Hz)

Opt. A11

India power plug (50 Hz)

Opt. A12

Brazil power plug (60 Hz)

Opt. A99

No power cord

Opt. L0

English manual

Opt. L1

French manual

Opt. L2

Spanish manual

Opt. L3

Japanese manual

Opt. L4

Portuguese manual

Opt. L5

Simplified Chinese manual

Opt. L6

Korean manual

Opt. L7

Russian manual

Opt. C3

Calibration Service 3 Years

Opt. C5

Calibration Service 5 Years

Opt. D1

Calibration Data Report

Opt. D3

Calibration Data Report 3 Years (with Opt. C3)

Opt. D5

Calibration Data Report 5 Years (with Opt. C5)

Opt. R5

Repair Service 5 Years (including warranty)

• RSA500 series warranty: 3 years.

Tablets ordered separately

The Panasonic FZ-G1 Toughbook tablet controller is recommended for use with the RSA500A series for portable field applications. The Windows 10 version of the tablet is available for purchase from Panasonic at https://na.panasonic.com/us/computers-tablets-handhelds/tablets/tablets/toughbook-g1 and other third party Web sites.

A variety of optional, licensed applications are available for purchase for SignalVu-PC. These licenses can be associated with and stored on either your PC or any RSA300 series, RSA500 series, RSA600 series, and RSA7100A spectrum analyzers. Licenses can be purchased as an option to your hardware or separately as a Node-locked or a Floating license.

Contact your local Tektronix Account Manager to purchase a license. If your purchased license is not ordered as an option to your instrument, you will receive an email with a list of the applications purchased and the URL to the Tektronix Product License Web page, where you will create an account and can then manage your licenses using the Tektronix Asset Management System (AMS):http://www.tek.com/products/product-license.

AMS provides an inventory of the license(s) in your account. It enables you to check out or check in a license and view the history of licenses.

Optional applications are enabled by one of the following license types.

The following SignalVu-PC license options are available.

Tektronix offers a wide variety of adapters, attenuators, cables, impedance converters, antennas and other accessories for the RSA500A series.

General-purpose RF cables

012-1738-00

Cable,50 Ω, 40 inch,type-N(m) to type-N(M)

012-0482-00

Cable, 50 Ω, BNC (m) 3 foot (91 cm)

174-4977-00

Cable, 50 Ω, straight type-N (m) and angled type-N (m) connector, 1.6 foot (50 cm)

174-5002-00

Cable, 50 Ω, type-N (m) to type-N (m) connector, 3 foot (91 cm)

Adapters

103-0045-00

Adapter, coaxial, 50 Ω type-N(m) to type-BNC(f)

013-0410-00

Adapter, coaxial, 50 Ω type-N (f) to type-N (f)

013-0411-00

Adapter, coaxial, 50 Ω type-N (m) to type-N (f)

013-0412-00

Adapter, coaxial, 50 Ω, type-N(m) to type-N(m)

013-0402-00

Adapter, coaxial, 50 Ω type-N (m) to type-N 7/16(m)

013-0404-00

Adapter, coaxial, 50 Ω type-N(m) to type-7/16 (f)

013-0403-00

Adapter, coaxial, 50 Ω type-N(m) to type DIN 9.5(m)

013-0405-00

Adapter, coaxial, 50 Ω type-N(m) to type-DIN 9.5(f)

013-0406-00

Adapter, coaxial, 50 Ω type-N(m) to type-SMA(f)

013-0407-00

Adapter, coaxial, 50 Ω type-N(m) to type-SMA(m)

013-0408-00

Adapter, coaxial, 50 Ω type-N(m) to type-TNC(f)

013-0409-00

Adapter, coaxial, 50 Ω type-N(m) to type-TNC(m)

Attenuators and 50/75 Ω pads

013-0422-00

Pad, 50/75 Ω, minimum loss, type-N(m) 50 Ω to type-BNC(f) 75 Ω

013-0413-00

Pad, 50/75 Ω, minimum loss, type-N(m) 50 Ω to type-BNC(m) 75 Ω

013-0415-00

Pad, 50/75 Ω, minimum loss, type-N(m) 50 Ω to type-F(m) 75 Ω

015-0787-00

Pad, 50/75 Ω, minimum loss, type-N(m) 50 Ω to type-F(f) 75 Ω

015-0788-00

Pad, 50/75 Ω, minimum loss, type-N(m) 50 Ω to type-N(f) 75 Ω

011-0222-00

Attenuator, fixed, 10 dB, 2 W, DC-8 GHz, type-N(f) to type-N(f)

011-0223-00

Attenuator, fixed, 10 dB, 2 W, DC-8 GHz, type-N(m) to type-N(f)

011-0224-00

Attenuator, fixed, 10 dB, 2 W, DC-8 GHz, type-N(m) to type-N(m)

011-0228-00

Attenuator, fixed, 3 dB, 2 W, DC-18 GHz, type-N(m) to type-N(f)

011-0225-00

Attenuator, fixed, 40 dB, 100 W, DC-3 GHz, type-N(m) to type-N(f)

011-0226-00

Attenuator, fixed, 40 dB, 50 W, DC-8.5 GHz, type-N(m) to type-N(f)

Antennas

119-8733-00

Antenna, Active. GPS & GLONASS, magnetic mount, 5M cable, 3V, 8ma SMA connector, RG-174 Cable

119-8734-00

Antenna, Active, GPS and Beidou, magnetic mount, 5M cable, 3V, 8ma SMA connector, RG-174 Cable

DF-A0047

Directional antenna, available from Alaris www.alarisantennas.com/ 20-8500 MHz, with electronic compass and preamp ¹⁸

016-2107-00

Transit case for DF-A0047 and DF-A0047-01¹⁸

119-6594-00

Yagi antenna, 825-896 MHz forward gain (over half-wave dipole): 10 dB

119-6595-00

Yagi antenna, 895-960 MHz forward gain (over half-wave dipole): 10 dB

119-6596-00

Yagi antenna, 1850-1990 MHz forward gain (over half-wave dipole): 9.3 dB

119-6597-00

Beam antenna, 1850 to 1990 MHz

119-6970-00

Magnetic mount antenna, 824 MHz to 2170 MHz (requires adapter 103-0449-00)

Filters, probes, demonstration board

119-7246-00

Pre-filter, general purpose, 824 MHz to 2500 MHz, type-N (f) connector

119-7426

Pre-filter, general purpose, 2400 MHz to 6200 MHz, type-N (f) connector

119-4146-00

EMCO E/H-field probes

E/H field probes, lower cost alternative

Available from Beehive http://beehive-electronics.com/

011-0227-00

Bias-T, type N(m) RF, type N(f) RF+DC, BNC(f) Bias, 1 W, 0.5 A, 2.5 MHz-6 GHz

EMI-NF-PROBE

Near Field Probe set (Tebox TBPS01)

Additional batteries and Cables

065-1004-00

Replacement battery pack for RSA500A series

016-2109-01

Additional soft carry-case with shoulder strap

174-6810-00

Additional USB 3.0 cable (2 M), A-A connection, screw lock

Recommended third party equipment and accessories

Recommended portable tablet controllers:

Windows 10 tablet PCs available from Panasonichttp://www.panasonic.com:

FZ-G1

Toughpad, Fully rugged 10.1", Windows 10 Pro 64-Bit, Intel^® Core™ i5 vPro™, 2^nd USB3.0 Port

Windows 10 tablet PCs available from Dellwww.dell.com:

7220

Latitude Rugged Extreme, 11.6”, Windows 10 Pro 64-Bit, Intel^® Core™ i5 vPro™, 16 GB RAM

Windows 10 tablet PCs available from Microsoftwww.microsoft.com:

Surface Pro 7

2-in-1 laptop 12.3”, Windows 10 Pro 64-Bit, Intel^® Core™ i5/i7 vPro™, 16 GB RAM

EMC accessories available from Com-Powerwww.com-power.com:

CLCE-400

RF current probe 10 kHz to 400 MHz

ABF-900A

Biconical antenna 25 MHz to 300 MHz

ALC-100

Compact Log Periodic antenna 300 MHz to 1 GHz

PAM-103

Preamplifier 1 MHz to 1 GHz

AT-812

Antenna Tripod 0.8 to 1.5m height range

EMC accessories available from Tekboxwww.tekbox.com:

TBPS01

Near field probe set, H20, H10, H5, and E5

TBCP1-150

RF current monitoring probe 10 kHz to 250 MHz

TBLC08

Line impedance stabilization network (LISN) 50uH AC

TBOH01

Line impedance stabilization network (LISN) 5uH DC

TBFL1

Transient limiter 150 kHz to 30 MHz

TBWA2

Near field probe amplifier 20 dB

Spectrum monitoring and direction-finding antennas from Alaris Antennaswww.alarisantennas.com:

DF-A0047

Directional antenna, 20-8500 MHz, with electronic compass and preamp

DF-A0047-01

Frequency range extension for DF-A0047 directional antenna, 9 kHz-20 MHz Upgrade

Calibration kits from SPINNER products.spinner-group.com

533863R000

Calibration kit, 3-in-1, open, short, load, DC to 6 GHz, Type-N(f), 50 ohm

533864R000

Calibration kit, 3-in-1, open, short, load, DC to 6 GHz, Type-N(m), 50 ohm

Transit cases available from Pelican www.pelican.com and associated distribution partners

IM2720

Pelican hard transit case, 22" × 17" × 10" interior

A variety of phase-stabilized cables are available for the RSA500 tracking generator when used with the optional cable and antenna measurements software.

Calibration kits can be used to improve the factory calibration of the tracking generator when equipped with application SV60-Return loss, VSWR, cable loss, and distance to fault.

These phase-stabilized cables are high performance cables that are phase-stable to +- 2 degrees at 7.5 GHz, with return loss less than -20 dB. Velocity constant is 0.78. Loss at 7.5 GHz specified to be less than -1.05 dB (0.6 m), -1.61 dB (1.0 m), -2.30 dB (1.5m) (all values nominal).

Calibration kits

Recommended calibration kits available from Spinner at https://products.spinner-group.com/rf/test-measurement/vna-test-measurement

Phase-stabilized cables

012-1745-00

Type-N (m) to type-N (f), 5 ft or 1.5 m

012-1746-00

Type-N(m) to type-N(m), 5 ft or 1.5 m

012-1747-00

Type-N(m) to 7/16(f), 60 cm (23.6 in.)

012-1748-00

Type-N(m) to 7/16(f), 3.28 ft or 1 m

012-1749-00

Type-N(m) to 7/16(f), 5 ft or 1.5 m

012-1750-00

Type-N(m) to 7/16(m), 3.28 ft or 1 m

012-1751-00

Type-N(m) to 7/16(m), 5 ft or 1.5 m

012-1752-00

Type-N(m) to 7/16(m), 60 cm (23.6 in.)

012-1753-00

Type-N(m) to DIN 9.5(f), 60 cm (23.6 in.)

012-1754-00

Type-N(m) to DIN 9.5(f), 3.28 ft or 1 m

012-1755-00

Type-N(m) to DIN 9.5(f), 5 ft or 1.5 m

012-1756-00

Type-N(m) to DIN 9.5(m), 3.28 ft or 1 m

012-1757-00

Type-N(m) to DIN 9.5(m), 5 ft or 1.5 m

012-1758-00

Type-N(m) to DIN 9.5(m), 60 cm (23.6 in.)

012-1759-00

Type-N(m) to TNC(f), 3.28 ft or 1 m

012-1760-00

Type-N(m) to TNC(f), 5 ft or 1.5 m

012-1761-00

Type-N(m) to TNC(f), 60 cm (23.6 in.)

012-1762-00

Type-N(m) to TNC(m), 60 cm (23.6 in.)

012-1763-00

Type-N(m) to TNC(m), 3.28 ft or 1 m

012-1764-00

Type-N(m) to TNC(m), 5 ft or 1.5 m

012-1765-00

Type-N(m) to type-N(f), 60 cm (23.6 in.)

012-1766-00

Type-N(m) to type-N(f), 3.28 ft or 1 m

012-1767-00

Type-N(m) to type-N(m), 3.28 ft or 1 m

012-1768-00

Type-N(m) to type-N(m), 60 cm (23.6 in.)

012-1769-00

Type-N(m) to type-SMA(f), 60 cm (23.6 in.)

012-1770-00

Type-N(m) to type-SMA(f), 3.28 ft or 1 m

012-1771-00

Type-N(m) to type-SMA(f), 5 ft or 1.5 m

012-1772-00

Type-N(m) to type-SMA(m) 60 cm (23.6 in.)

012-1773-00

Type-N(m) to type-SMA(m), 3.28 ft or 1 m

012-1774-00

Type-N(m) to type-SMA(m), 5 ft or 1.5 m